An in-floor safe is one of the most discreet ways to protect your valuables. Set into concrete with only a cover plate at floor level, it can sit under carpet, a rug or furniture where nobody knows it’s there. But the weeks straight after installation matter more than most people realise. Here’s what to expect, and how to keep your safe and everything in it in good shape.
The same care steps also sit at the top of our in-floor safes page, which is where the QR code on the information card that ships with your safe takes you.
Quick answer
After your in-floor safe is installed, keep the door open until no moisture remains in the concrete around the safe. This applies to every DF Series model, and can take up to 4 to 6 weeks in some conditions. Once it’s completely dry, add a silica gel bag, check it every 2 weeks, set your own code, and register your warranty.
Before installation: is your floor suitable?
Dominator DF Series in-floor safes are designed to be set into concrete. A few things are worth knowing before you book an installer:
- New pour or existing slab, it doesn’t matter. The same guidance applies to any installation.
- There’s no minimum slab depth. The installer goes right through the slab, sets the safe in place and concretes back around it.
- Underfloor heating rules it out. An in-floor safe can’t be used where there is underfloor heating.
- Timber floors need a custom installation. Talk to your dealer before you plan anything.
How much does in-floor safe installation cost?
A standard concrete installation typically costs between $800 and $1,200. Every installation is subject to a quote from your dealer. Installation is arranged through your Dominator dealer, who can also help you choose the right size.
Choosing the right model
The DF Series comes in four sizes:
- DF-1: 9 L, with a removable lid, a 260 x 280 mm base plate and a $10,000 cash rating. Compact, for watches and small valuables.
- DF-2: 19 L, with 5 locking bolts, a 345 x 380 mm base plate and a $20,000 cash rating.
- DF-3: 35 L, the same height as the DF-2 with more depth, a 345 x 380 mm base plate and a $20,000 cash rating.
- DF-4: 59 L, the wide-format model, with a 360 x 615 mm base plate and a $20,000 cash rating.
Every model is available with your choice of lock (more on that below).
Why new concrete and closed doors don’t mix
New concrete holds a lot of water and keeps releasing it for weeks after it’s poured. If the safe door is closed during this time, that moisture gets trapped inside. The result can be condensation, rust, mould and damage to anything you’ve stored.
That’s why every Dominator in-floor safe now ships with an information card that says one thing in big letters: keep the door open. This applies to every DF Series model.
Curing time varies with weather, ventilation and slab depth, so check the safe regularly. Don’t put anything inside until it is completely dry. In some conditions this can take up to 4 to 6 weeks.
Before you use it for the first time
Once the concrete has cured:
- Check the inside is completely dry, with no condensation on the walls or under the door, so it’s ready for permanent use.
- Put a moisture absorber or silica gel bag inside.
- Change the factory code or combination and test it a few times with the door open before you close it.
Ongoing care: desiccant and airflow
Keeping moisture out is an ongoing job, not a one-off.
- Check your desiccant every 2 weeks.
- Not sure if it’s still working? Weigh it. Silica gel bags absorb about 10% of their starting weight. Weigh a new bag and note the figure. When it’s around 10% heavier, it’s full and needs replacing.
- Let some air in. Open the safe every now and then, especially in humid weather.
- Keep it clean. Keep the door frame and edges clear of dirt, grit and water.
- Bag sensitive items if you don’t open the safe often. If you don’t open your safe very often, store documents, cash, photos and electronics in sealed bags or containers. That protects sensitive items if condensation or moisture builds up from the surrounding conditions.
Signs of moisture include condensation on the door, a musty smell, surface rust or damp contents. If you find any, empty the safe, leave the door open until it’s fully dry, then replace the desiccant.
Are in-floor safes waterproof?
No. In-floor safes are not intended to be waterproof. The doors are not sealed, so any leak from above can get inside the safe. If your safe is somewhere water could reach it, such as near a wet area, you’ll need to add your own provisions to protect it.
It’s also worth knowing that damage caused by moisture, condensation or improper installation is not covered by the warranty. A few minutes of care every couple of weeks is the best protection you’ve got.
Locks: getting started
Each DF Series safe comes with your choice of lock:
- Tecnosicurezza Pulse 2 electronic lock. The factory code for most electronic locks is 123456. Change it to your own code straight away, and avoid easy codes like birthdays. Use good-quality alkaline batteries such as Duracell. Rechargeable and lithium batteries are not recommended. A long beep when opening means the battery is low. Pulse 2 instructions | video
- 3 wheel mechanical combination lock. Set to 50 from the factory. No batteries needed. Combination instructions | how to open | how to change the combination
- Ross 700 key lock. An Australian made key lock with no batteries to worry about.
Full instructions are supplied inside the safe, and there are more how-to videos on our YouTube channel at youtube.com/@IntSafe.
Lost your key or forgotten your code?
Contact your dealer. It’s the same process as for any of our safes. Please don’t try to force the safe open, as that can cause permanent damage.
Register your warranty
Register your safe at dominatorsafes.com.au/warranty-registration/. Registering within 14 days of purchase gives you access to the extended warranty. You’ll need your model, serial number and proof of purchase.
Need help?
Start with your dealer. They’re your first stop for advice, installation, service, lost keys and forgotten codes. You can also call us on 1300 366 462 or email info@dominatorsafes.com.au.
Better safe… than sorry.
Request a Quote
Request a free quote on a and one of our experts will be in touch.
Protect
Burglary or fire can be devastating. You can reduce the potential impact in your life by properly securing your most valuable possessions in a high security, fire-resistant safe.
Quality
Strict and highly detailed quality inspections are undertaken at multiple stages throughout the manufacturing process to ensure the best possible product gets delivered every time.
Secure
As unfortunate as it is, there is a growing need to secure your business and personal valuables from theft and a quality burglar safe is the best place to start.
Useful materials
All You Need